L1 BOSE Radiator System Model 2

• L1 Model II Cylindrical Radiator loudspeaker top:
• Dimensions: 43-1/2''H x 3-1/2''W x 4''D (1.1 m x 9.0 cm x 10.5 cm)
• Weight: 16.3 lbs (7.4 kg)
• L1 Model II Cylindrical Radiator loudspeaker bottom:
• Dimensions: 43-1/2''H x 3-1/2''W x 4''D (1.1 m x 9.0 cm x 10.5 cm)
• Weight: 17.4 lbs (7.9 kg)
• L1 Model II power stand:
• Dimensions: 5''H x 10''W x 27''D (12.8 cm x 26.2 cm x 69.2 cm)
• Weight: 23.7 lbs (10.7 kg)
• B1 Bass module:
• Dimensions: 15''H x 10-1/4''W x 17-3/4''D (38.0 cm x 26.0 cm x 45.0 cm)
• Weight: 25.1 lbs (11.4 kg)
  
• AC power rating: 100-120V 50/60Hz 500W (USA/Canada)
  
• 1/4" analog input
  
• ToneMatch port for T1 ToneMatch audio engine
  
• Neutrik NL4 bass module out
  
• 1/4" bass line output
  

BOSE T1 ToneMatch Audio Engine

• Main Inputs/Outputs
  
• Mic/line inputs (1 3): Analog channels with combination connectors accepting balanced XLR or unbalanced 1/4" TRS audio cables.
  
• Line inputs (4/5, L/R): Analog channels for stereo connections to keyboards, mixers and computers. Inputs accept balanced 1/4" TRS cable. Edit control affects both channels.
  
• Trim controls and signal/clip LEDs (1 4/5): Adjust levels of input signals. Green/yellow/red LEDs show signal status and help you set gain levels properly.
  
• Preamp outputs (1 3): For connecting channels' dry output signals to recording gear or other amplifiers via balanced 1/4" TRS cable.
  
• Aux output: Use with aux mode to create independent submix of channels 1 4/5 to route to other amplifiers or recording gear.
  
• Master output: Analog output for connecting to additional L1 systems, amplifiers or recording gear via balanced 1/4" TRS cable. Select from pre- or post-master volume settings.
  
• ToneMatch port: Connect digital output of engine to L1 Model II power stand via included ToneMatch digital cable. Single cable also supplies power to engine.
  
• USP Port: Update ToneMatch audio engine and back up scenes via USB connection to your computer.
  
• Dimensions: 2 2/3''H x 6 1/2''W x 8 1/4''D (6.76 cm x 16.6 cm x 20.9 cm)
  
• Weight: 2.1 lbs (1.0 kg)
  
• A/D conversion: 24-bits
  
• Sampling rate: 48 kHz
  
• PC requirements (for USB port): Windows 2000, 2000 Pro, XP
  

L1 BOSE Radiator System Model 1(used for backup or large venues only)

• L1 Cylindrical Radiator™ loudspeaker (assembled height) • 83 1/5"H x 3 1/2"W x 4"D • (212.1 x 8.9 x 10.5 cm) • 65.5 lbs (29 kg)
• PS1 Power Stand • 5"H x 26"W x 26"D • (12.7 x 66 x 66 cm) • 35 lbs. (16 kg)
• L1 Cylindrical Radiator™ loudspeaker (top section) • 43"H x 3 1/2"W x 4"D • (109.2 x 8.9 x 10.5 cm) • 14.5 lbs. (6 kg)
• L1 Cylindrical Radiator™ loudspeaker (bottom section) • 43"H x 3 1/2"W x 4"D • (109.2 x 8.9 x 10.5 cm) • 16.0 lbs. (7 kg)
• R1 Remote Control • 1 3/5"H x 2 4/5"W x 5 3/5"D • (4.0 x 7.1 x 14.1 cm) • 0.6 lbs. (0.27 kg)
• Spectral range: D below E string on the bass guitar, and above
• Output: rock concert levels can be achieved if desired on stage and in an audience of several hundred.

Mackie CFX12 Mark II Mixing Desk (backup only)

• High-headroom mic preamps with RF rejection
• 12 channels (8 mic/line mono, and 2 stereo line channels)
• 32-bit EMAC digital effects with 9 reverbs, 4 delays, phaser, chorus, flange; 2 parameter controls + EFX wide spatial expander
• External and internal EFX sends
• EFX to Monitor control
• 9-band stereo graphic equalizer
• Inserts on all mic channels and main mix
• True 4-bus design with direct sub outs and L/R assign
• 2 Pre/Post Aux sends and internal/external FX level sends on each channel
• 3-band EQ with swept mid (100Hz to 8kHZ) on mic/line channels
• 4-band EQ on stereo line channels
• Pan, Mute, PFL solo on each channel
• Inserts and 100Hz low-cut filters on all mic/line channels
• Subwoofer output from built-in 18dB/oct. 75Hz crossover
• Ingenious BREAK switch
• Headphone output with level control
• Tape/CD inputs with level control assignable to Main Mix via Break switch
• Logarithmic taper 60mm faders
• 48V phantom power
• 12V BNC lamp jack

• Polar pattern - Supercardioid
• Transducer type – Dynamic
• Frequency ranges - 740-764 MHz / 774-798 MHz / 798-822 MHz / 850-874 MHz
• Modulation – FM
• Nominal deviation - ± 40 kHz
• Radiated transmitter power  - >10 mW
• Compander system - NE572
• Gain - Switchable with integrated switch -10 dB (= 0.7 mV/Pa)
• AF transmission range - 65 - 16,000 Hz
• S/N ratio rel. to 1 Pa - > 110 dB
• T.H.D. - < 0.5% at 1 kHz
• Transmission range - > 100 m
• Power supply - 2 x 1.5 V batteries (AA) or rechargeable batteries
• Operating time - approx. 20 hrs. with alkaline batteries
• Dimensions - Length: 258 mm / Shaft: 33/37 mm
• Weight - 220 g

• 5 channel intelligent goboflower
• Master/slave linkable
• Sound activated by built in mic
• Pre programmed light show for immediate operation
• Gobo/colour wheel with 15 gobos plus shutter,12 one colour,one bi colour,one
• four colour plus white on the same wheel
• Adjustable focus
• Controllable via any universal dmx controller
• Fan cooled
• A1/259 250w lamp

• Professional black aluminum Par 64 Can
• DMX Channels: 4
• Blackout/static/dimmer/strobe
• Sound active mode
• Auto mode
• Static colour mixing via dip switches
• RGB colour mixing via dip switches
• Internal programs with sound activation
• Speed control
• Master/Slave
• Linkable with LEDJ RGB DMX Flood
• 108 Ultra bright 10mm LED`s
• Power consumption: 16 watts
• Beam: 15 degrees
• Lamp life: 100,000 hours
• Power supply: 230v
• Dimensions: 275 x 230 x 210mm
• Weight: 1.2kgs
  

• Double liting to enhance any stage
• Colourmix hand controller
• Colourmix foot controller
• 3 section lightweight alloy lighting stands up to 4m
• K1 500w Halogen Lamps
• All connects to form unbeatable mobile lighting system